Solutions Products Support About Us Find a Distributor Contact Us
Solutions Products Support About Us
Solutions Products Support

WEDOLiT

Optimize metal-forming processes with WEDOLiT™ pipe and tube expansion, forming and corrosion control fluids

  • offer customized product solutions
  • deliver more reliable, efficient metal forming and pipe and tube expansion
  • ensure a smooth process flow, long tool life, and low fluid consumption
  • provide optimum corrosion protection

Number of products in category is 25

WEDOLiT AS 1012

Dewatering-fluid 104°F (40°C) flash point

WEDOLiT AS 1012 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions or synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT AS 2251

Long term DW Fluid 104°F (40°C) flash point

WEDOLiT AS-2251 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behavior
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Very low

WEDOLiT AS 2603

High-Protection-Waxdispersion-Fluid 104°F (40°C) flash point

WEDOLiT AS 2603 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
  • Good protection for outdoor storage
  • It´s recommended to homogenise the product before use or after a longer storage period
  • Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

WEDOLiT AS 4116

High-Protection-DW-Fluid 140°F (60°C) flash point, thin film

WEDOLiT AS-4116 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing of rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behavior
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low

WEDOLiT AW 8321 (K 110)

Water-miscible High-performance Fluid

WEDOLiT AW 8321 is universally applicable for parts cleaning and corrosion protection. This mineral oil based product is not only suitable for steel, but also for non-ferrous metals. Utilizing the latest technology, AW 8321 offers the possibility for a boron and formaldehyde free application.

  • The product forms a stable emulsion, regardless of the concentration. Due to the electrolyte and temperature stability, an application in heated baths is possible (recommended temperature 140 - 176°F, (60 - 80°C))
  • Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)
  • Easily removable with solvents or alkaline industrial cleaners
  • For the corrosion protection it´s important that treated parts are completely dry before packaging. Dependent on the concentration a minimal to slightly noticeable film is formed on the metal surface
  • Very good compatibility with VCI foils
  • Outstanding material compatibility (even at higher concentration)

WEDOLiT CS 8208

Water-miscible, fully synthetic coolant

WEDOLiT CS 8208 is suitable for ultrasonic testing systems. The product is also suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 5 - 10%). Not suitable for the manufacturing of workpieces made of zinc, aluminum and their alloys.

  • Offers high cooling- and flushing properties with a very good wetting behavior
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a good skin compatibility
  • Due to its thermal stability, the product can be used in almost the whole process chain of welded tubes (forming, welding, calibration, sawing)

WEDOLiT EP 1090-E

High performance expander oil

WEDOLiT EP 1090-E is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents the stick-slip- effect due to the high content of polar additives.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 540 ES

Expander Oil, Easy-splitting Technology, mineral oil based

WEDOLiT EP 540 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and expander heads and can be easily separated into water and oily waste by utilizing specific additives
  • Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760 E

Expander oil

WEDOLiT EP 760 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760 ES

Expander Oil, Easy-splitting Technology, mineral oil based

WEDOLiT EP 760 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by utilizing specific additives
  • Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT FN 1190-2300

High-performance forming oil

WEDOLiT FN 1190-2300 is a highly viscous, chlorine containing forming oil for tube drawing and other cold forming operations of stainless steel. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Soluble in chlorinated hydrocarbons

WEDOLiT FN 1571-2800

Drawing Brass and Copper Tubes

WEDOLiT FN 1571-2800 is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminum and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Evaporates at temperatures T ≥ 572°F, (300°C) without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 4455-55

Chlorine free stamping oil

WEDOLiT FN 4455-55 is a low viscous, water-insoluble lubricant for heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushing, or rolling.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a long tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 6160-90

High performance forming oil

WEDOLiT FN 6160-90 is a water-insoluble, chlorinated lubricant for deep drawing and other cold forming operations, e.g. wire drawing, extrusion, or thread forming of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes, or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 8830

Special forming oil

WEDOLiT FN 8830 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied on the outer diameter by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation
  • Stable cold start behavior, prevents stick-slip and chatter
  • Contributes to achieving dimensional accuracy
  • Pigments will remain on the surface after annealing and need to be removed (e.g. by pickling with HCl or HNO3) before further processing

WEDOLiT FN 8850-90

Drawing small diameter tubes, diesel injection

WEDOLiT FN 8850-90 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of steel. Due to the fact that the product also offers corrosion protection, no additional treatment is necessary (for short term storage). The undiluted product is usually applied by spraying, brushes, or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FS 3710

Evaporating Drawing-oil

WEDOLiT FS 3710 is a non-water soluble, synthetic cooling lubricant of low viscosity. It is applicable for drawing- and punching-operations of aluminium. Can be applied undiluted by spraying, flooding, brushing or rolling.

  • Good wetting of the metal surface
  • Nearly odourless
  • Despite the good lubrication properties, the product is characterised by a quick evaporation and high flash point
  • The working area should be sufficiently ventilated, due to the amount of volatile hydrocarbons

WEDOLiT FS 3910

Straight Cutting and Bending Oil

WEDOLiT FS 3910 is non-water-soluble cooling lubricant with low viscosity for punching- and bending operations on steel and zinc coated steel. The product is not applicable for the treatment of nonferrous metals.

  • Can be applied undiluted by spraying, flooding, brushing or rolling
  • Has a good spread effect, which causes an optimal even wettability of metal surfaces
  • Has a simultaneously cleaning effect
  • Contains a combination of aromatic free solvents with additives of esters and extreme-pressure compounds and is therefore practically odorless
  • Is marked by a very fast evaporation with high flash point

WEDOLiT FS 4710

Solvent base for aluminum stamping 158°F (70°C)

WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminum and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes, or by means of rollers.

  • Good spreading behavior, which leads to a uniform wetting of the metal surface
  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • If the product is finely dispersed, it evaporates after a short time without leaving any residue. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FW 1960

Soap for tube drawing operations

WEDOLiT FW 1960 is a water-soluble alkaline soap for heavy drawing operations of steel tubes. The product is usually used as an immersion bath (bath temperature 167 - 194 °F, (75 – 90 °C)).

  • The product is designed to react with the zinc phosphate layer (which acts as lubricant) to form a zinc soap. The zinc phosphate layer should be at least 4 μm (at heavy forming operations, e.g. cold extrusion, up to 10 μm). Due to specific additives, a maximum conversion of zinc phosphate and the drawing media occurs, which results in an optimal performance regarding degree and rate of deformation
  • Can be used in very low concentrations of 5 - 10% as an aqueous solution (tube drawing). The best results are obtained with water free media
  • Offers (in combination with a zinc phosphate layer) very high cross-sectional reduction and high drawing velocities – up to 100 m/min (steel tubes with standard cross-sectional reduction)

WEDOLiT FW 3500

Water-soluble, fully synthetic, good material compatibility

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

  • Offers very good high-pressure properties
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers very good skin compatibility


  • Recommended mixing ratio
  • Hydrofroming:  from 5 - 10%
  • Grinding:  from 3 - 6%

WEDOLiT FW 7651

Water-miscible, fully synthetic coolant for the whole tube welding line

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfills the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 4 - 6%

WEDOLiT FW 7661

Water-miscible, fully synthetic coolant

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  3 -5%

WEDOLiT FW 7840

Emulsion for the whole tube welding line

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040305) under the name WEDOLiT K 911.

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 7%

WEDOLiT N 52

Universal cutting oil

WEDOLiT N 52 is a mineral-oil based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems such as milling, sawing, or thread forming steel, aluminum, and non-ferrous metals*.
Approved by Rattunde & Co as a cutting oil for minimum quantity lubrication.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Very good wetting ability and film formation without adhesion
  • The outstanding cooling and lubrication properties lead to significantly reduced friction and wear and thus contribute to a long tool life
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Economical application
  • Easily removable with organic solvents or alkaline industrial cleaners